Vantec UGT-IS100R Manual do Utilizador

4+1 SATA II 300 IDE/PATA PCI-E Combo Host Card w/ RAID & Port Multiplier User Manual Model: UGT-IS100R All brand names and tradem

UGT-IS100R Page10 exit the BIOS. RAID 0+1 (Striping + Mirroring) 1. As the BIOS boots press Ctrl+J when prompted to enter the RAID BIOS. 2. At t

UGT-IS100R Page11 Delete RAID Disk Drive 1. As the BIOS boots press Ctrl+J when prompted to enter the RAID BIOS. 2. At the next screen select De

UGT-IS100R Page12 connection information, will be written to the replacement disk. Rebuild Mirror Drive When a failure to one member occurs, you w

UGT-IS100R Page13 Fup. During this (POST) process, the BIOS will show up and indicate the devices attached to it. Driver Installation For Windows®

UGT-IS100R Page14 on-screen instructions to complete the Windows installation. For An Existing Installation 1. Setup the RAID Array prior to d

UGT-IS100R Page15 directions below. 1. Setup the RAID Array prior to Windows installation. 2. Follow Microsoft’s Windows installation procedure.

UGT-IS100R Page16 Finstallation. 6. Restart Windows to complete the installation. For Windows® Vista or A New Installation A new installation re

UGT-IS100R Page17 F1. Setup the RAID Array prior to driver installation and boot up to Windows. 2. Please insert the CD driver bound with 4+1 SA

UGT-IS100R Page18 F3. At the Windows Setup screen, press Load Driver to install the RAID driver. 4. Insert the floppy disk, please select JMicro

For Windows® Server 2008/7 (32-bit) For New Installation 1. Setup the RAID Array prior to Windows installation. 2. Follow Microsoft’s Windows instal

UGT-IS100RPage2 Table of Contents 1. Features and Benefits ... 3 2. Bus Interface...

UGT-IS100R Page20 Finto your CD-ROM Drive. 3. At the Windows desktop, click Start, then Run. 4. Type D:\UGT-IS100R\2000_XP_2003_Vista\setup.exe,

7. Follow the on-screen instructions to complete the installation. UGT-IS100R Page21 For An Existing Installation 1. Setup the RAID Array prior

UGT-IS100R Page22 Controller: -JMicron JMB36X Controller should be displayed Windows® Vista: Double click Storage controllers: -JMicron JMB36X Co

UGT-IS100RPage3 Features and Benefits z Compliant with one-lane 2.5Gb/s PCI Express specification z Compliant with Serial ATA 1.0 specification

UGT-IS100RPage4 System Requirements z PCI Express-enabled system with one available PCI Express slot z Windows® 2000, XP/2003/Vista/2008/7 (32/6

default, Port CON1 & CON2 are working. UGT-IS100RPage5 Jumper Settings JP Description Active Port 1-2 close Enable SATA Port CON1 J1-J4

UGT-IS100RPage6 CON3 1-2 close Enable SATA Port CON2 J5-J8 2-3 close Enable SATA Port CON4 Hardware Installation 1. Turn Off the power to your

UGT-IS100RPage7 RAID Arrays RAID Arrays are setup in the 4+1 SATA II 300 IDE/PATA PCI-E Combo Host Card w/ RAID & Port Multiplier ’s BIOS. T

UGT-IS100RPage8 “space” key to mark the selected disk, then press Enter. 6. Please use arrow keys ↑ and ↓ to select chunk size from 4K, 8K, 16K,

UGT-IS100RPage9 7. When asked Created RAID on the select HDD (Y/N)?, press Y to accept. 8. At the next screen select Save And Exit Setup, press E